We've encountered this post involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the web and figured it made good sense to talk about it with you on this site.
Mounting a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily accessible, the project can move easily; if you have to open a wall to eliminate the old bathtub as well as place the new tub, the job is much harder. In either situation, the job is within a residence handyman's skills, although you will require a helper to move out the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This short article will certainly assist you set up a brand-new bathtub in your restroom if you have already gotten a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipelines.
Your devices and also product list need to comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be fairly problematic due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using both wood boards under its feet, place the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water and check all joints as well as new pipework for leaks and also tighten them if necessary. Fill up the tub as well as also check the overflow outlet as well as the regular outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been used at least once as this will settle it right into its last position.
Getting ready for the Setup
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with dampness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealer can split rather early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader about A Step-by-Step Guide to Installing a Bathtub, I think sharing that piece was a good idea. Please set aside a second to share this blog posting if you appreciated it. Thanks so much for taking the time to read it.
Find Out More